A seamless, easy-to-clean garage floor built on a properly ground slab, installed by a local crew serving the Santa Clarita Valley and nearby communities.
Garage floor epoxy is a coating system that bonds to a prepared concrete slab and turns it into a seamless, easy-to-clean surface. Elevate Epoxy Flooring diamond grinds each garage, repairs cracks and joints, applies a moisture-barrier epoxy basecoat, and finishes with a UV-stable polyaspartic topcoat for homes across the Santa Clarita Valley.
A bare garage slab takes a beating that a living room floor never sees. Oil drips, cleaner spills, hot tires, dropped tools and tracked-in grit all work into the pores of raw concrete, which is why so many garage floors look stained and dusty within a few years of construction. Paint and thin roll-on kits tend to peel because they sit on top of the surface instead of locking into it. A professionally installed epoxy system works differently. The concrete is mechanically opened up with diamond grinding, so the coating grips a real bonding profile and becomes part of the slab rather than a film lying on it.
Elevate Epoxy Flooring is a service-area business based in Santa Clarita, and our crews drive to garages throughout the Santa Clarita Valley, the San Fernando Valley, Simi Valley and the Antelope Valley. Every job starts with a look at your slab, a conversation about how you use the space, and a clear plan for the system that fits. Most residential garages are finished with the standard flake process in a single day, but we also install solid color, metallic and quartz systems when a different look or a rougher slab calls for it. The finished floor carries a limited lifetime adhesion warranty.
The work follows a fixed order so nothing gets skipped. We grind the entire slab with diamond tooling to remove laitance and old sealers, then vacuum away the dust. Cracks and control joints are cleaned and filled with a repair material, and vertical coating is applied where the floor meets the walls and the door threshold. The moisture-barrier epoxy basecoat goes down next, followed by a full-rejection flake broadcast that covers the wet coating until no bare spots remain. Once the basecoat firms up, we scrape and vacuum the surface so loose flake does not show through, and we seal everything under the topcoat.
Garage slabs come with quirks. Hairline shrinkage cracks, saw-cut joints, old oil stains, pitted surfaces, patched areas and leftover adhesive from mats or tiles all show up regularly in the Santa Clarita Valley. Grinding handles most surface contamination, and crack and joint repair fills the movement lines before any coating goes on. Moisture vapor rising through concrete is another common cause of bubbling, which is why we use a moisture-barrier epoxy basecoat rather than a thin primer. If a crack is actively moving or a section of concrete has failed, we point that out at the estimate so you know what a coating can and cannot hide.
Most garage floors are finished in a flake blend that gives the surface a speckled, slightly textured look. Flakes hide small marks and dust far better than a plain gloss color, and the texture gives shoes and tires a little extra grip. Color options are available across the flake, marble flake, metallic and solid collections, and our color chart lets you compare them before you decide. Day to day care is simple: sweep or dust mop, then wash with a mild cleaner and a soft mop or deck brush. Wipe up chemical spills when you notice them. The topcoat is chosen to resist hot-tire pickup, so parking a warm car does not mark the surface.
Homeowners choose epoxy for very different reasons. Some are converting a garage into a gym, workshop or hobby room and want a floor that looks finished. Others are preparing a home for sale and want a bright, clean impression for buyers. Car enthusiasts like how a coated floor shows off a vehicle and makes drips easy to spot. Families simply want a surface that wipes clean after a muddy sports season. A coated floor also suits newer homes with bare builder-grade concrete as well as older homes with worn slabs. If your floor has serious damage, we will explain the realistic options before any work starts.
With no grout lines or seams, spills stay on top and wipe up quickly. The continuous coating also avoids the gaps where dirt and moisture collect under tiles or mats.
Diamond grinding creates a bonding profile that the epoxy grips, which helps the coating resist peeling, lifting and chipping under daily garage traffic and vehicle weight.
The moisture-barrier epoxy basecoat slows vapor coming up through the slab, helping prevent the blistering and cloudiness that thinner coatings can show on damp concrete.
A UV-stable polyaspartic topcoat holds up to sunlight coming through the garage door, so the flake colors stay true instead of yellowing or chalking as the years pass.
The topcoat stands up to oil, brake fluid, household cleaners and hot-tire pickup, so ordinary garage use does not leave permanent marks or dull spots on the floor.
Our systems are VOC-free, which keeps the job low in odor and easier to live with when the garage is attached to your home. A limited lifetime adhesion warranty backs the work.
The standard flake garage system is finished in one day, with grinding through topcoat completed in a single visit. Light foot traffic is generally fine once the topcoat has set, and we give you a specific time on the day of the job. Hold off on dragging heavy items or returning vehicles until the recommended wait has passed, then ease back into normal use while the coating reaches full cure. Solid color takes 3 days, quartz 2-3 days and metallic 3-4 days.
Flake is the usual choice for a garage because it hides wear, adds texture and installs in one day. Pick solid color when you want a clean, uniform look with a smooth finish. Metallic brings dramatic depth and suits showpiece garages or finished living spaces. Quartz gives a harder, more textured surface for heavy traffic. If you only want a protected, natural concrete look with no color coat, grind and seal is a lighter option. We can lay the choices side by side at your estimate.
Typical ranges for the Santa Clarita Valley. Minimum project $2,600. Commercial and industrial work is quoted after a site visit.
| System | Price per sq ft | Typical project |
|---|---|---|
| Flake system (garage, up to 400 sq ft) | $6.50 – $10 per sq ft | $2,600 – $4,000 |
| Solid color system | $9.50 – $11.50 per sq ft | $3,800 – $4,600 |
| Metallic epoxy system | $12.50 – $18.50 per sq ft | $5,000 – $7,400 |
| Quartz & sand finish system | $9 – $16.50 per sq ft | $3,600 – $6,600 |
| Grind & seal (clear sealer) | $6.50 – $9 per sq ft | $2,600 – $3,600 |
| Patio, driveway & pool deck | $8 – $12 per sq ft | $3,200 – $4,800 |
| Commercial & industrial | Quoted after a site visit | Quoted per project |
Prices and details reviewed October 2026. Project examples assume a two-car garage up to 400 sq ft. Free on-site measurement and written estimate. See the color chart to pick your color.
Yes, for most garages, epoxy is a good idea when the concrete is sound and the installer grinds the slab, repairs cracks, and uses a proper moisture-barrier basecoat with a UV-stable topcoat. A thin roll-on kit over unprepared concrete is where most disappointment comes from.
Read the answer →A 20x20 garage is 400 square feet. Our installed prices for it run from $2,600 to $4,000 for a flake system, with solid color, quartz, metallic, and grind and seal falling in other ranges. The final number depends on the system you choose and the condition of the slab.
Read the answer →Hot tire pickup is when warm tires soften or pull at a garage floor coating, leaving marks, ridges, or peeled patches where the tires sit. You prevent it with thorough diamond grinding, a well-bonded quality basecoat, a UV-stable polyaspartic topcoat, and giving the floor its full cure time before parking.
Read the answer →Usually yes. A properly installed epoxy and polyaspartic system resists oil, chemicals and hot-tire pickup, hides dust, wipes clean and gives a bare, stained slab a finished look. It works best on a sound slab that is diamond-ground and checked for moisture first. If the concrete is badly cracked or constantly damp, repair that first or ask us for a recommendation.
A 20x20 garage is about 400 square feet, a typical two-car garage. A flake system runs about $2,600 to $4,000, solid color $3,800 to $4,600, quartz $3,600 to $6,600, metallic $5,000 to $7,400 and grind and seal $2,600 to $3,600. Our minimum project is $2,600. Slab condition and repairs can change the final price, so we give a fixed written quote after a free measure.
The real downsides are a day or more without the garage, scratches or chips under heavy impact, a slippery surface when wet if it has no texture, and failures when preparation is skipped. Epoxy-only topcoats can also yellow in sun. We diamond-grind every slab, use flake or a slip additive for traction and finish with a UV-stable polyaspartic topcoat to limit those problems.
A well-prepared floor with a UV-stable topcoat keeps its color and most of its gloss. Expect light wear and fine scratches in the busiest spots, and flake finishes hide this best. Poorly prepared or epoxy-only floors can peel, stain or yellow. Our limited lifetime adhesion warranty covers the bond between the coating and your concrete.
Look for a local installer that grinds the slab, uses a moisture-barrier basecoat and a UV-stable topcoat, shows real prices and gives a written warranty. Elevate Epoxy Flooring is based in Santa Clarita and installs garage floors in Valencia, Newhall, Canyon Country, Saugus, Castaic, Stevenson Ranch, the San Fernando Valley, Simi Valley and the Antelope Valley. Call (661) 457-5812 for a free estimate.
The standard flake system is done in one day. Solid color takes 3 days, quartz 2-3 days and metallic 3-4 days. The schedule also depends on how much crack repair or surface correction your slab needs, and we confirm the timeline with you before work begins.
Peeling usually traces back to poor prep or trapped moisture. We diamond grind the slab to create a bonding profile, repair cracks and joints, and use a moisture-barrier epoxy basecoat. That preparation is what lets the coating hold up, and a limited lifetime adhesion warranty backs it.
Yes in most cases. Grinding removes surface contamination, and we clean out and fill cracks and joints before coating. Deep oil saturation or a moving crack may need extra attention, and we will tell you at the estimate what the coating can realistically cover.
Yes, the floor needs to be clear so the crew can grind and coat the whole slab. Move vehicles, shelving and loose items out ahead of time. If you have heavy workbenches or cabinets that are hard to move, mention them when you book so we can plan around them.
Hot-tire pickup is when heat from tires softens a weak coating and pulls it off the slab. A properly cured UV-stable polyaspartic topcoat over a well-bonded epoxy basecoat is chosen to resist it, so driving in after a long commute is not a problem.
Elevate offers a limited lifetime adhesion warranty on the coating. It is tied to the coating staying bonded to the slab, and it has limits like any warranty. Ask us for the written terms at your estimate so you can read exactly what is and is not covered.
For a garage you usually want both. An epoxy basecoat bonds to the slab and carries the color or flake, and a polyaspartic topcoat adds UV stability and resistance to hot-tire pickup. A polyaspartic topcoat also cures quickly, which is why most garages are finished in one day.
At our flake range of $6.50 to $10 per square foot, 1,000 square feet is about $6,500 to $10,000. A solid color system is about $9,500 to $11,500 and metallic about $12,500 to $18,500. We give a fixed written price after measuring the space and checking the slab.
Full-rejection flake over a moisture-barrier epoxy basecoat, sealed with a UV-stable polyaspartic topcoat. Installed in one day.
Learn more →A clean, seamless pigmented floor in gloss, satin or matte for garages, workshops, interiors and commercial spaces.
Learn more →Diamond-ground concrete finished with a clear sealer for a natural, low-maintenance floor at the lowest installed price.
Learn more →Call (661) 457-5812 or send the form at the top of the page. We reply the same day with a time to measure.